A. Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0
B. Router(config)# ip route 0.0.0.0 255.255.255.255 s0
C. Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0
D. Router(config)# ip route 0.0.0.0 0.0.0.0 s0
E. Router(config)# ip route any any e0

A. TK1(config)# ip route 0.0.0.0 0.0.0.0 E0
B. TK1(config)# ip route 0.0.0.0 255.255.255.255 S0
C. TK1(config-interface)# ip route 255.255.255.255 0.0.0.0 192.168.1.21
D. TK1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.21
E. TK1(config)# ip route 0.0.0.0 192.168.1.21 255.255.255.255
F. TK1# ip default-network 0.0.0.0 192.168.1.21 255.255.255.255

A. The default administrative distance is used.
B. The command is used to establish a static route.
C. The command is used to configure the router interfaces.
D. The command is used to establish a stub network.
E. The subnet mask for the source address is 255.255.255.0

A. The summarized address for all internal subnetted addresses.
B. A private IP address assigned to a host on the inside network.
C. A registered address that represents an inside host to an outside network.
D. A unique IP address used on an internal network
E. Non of the above

A. IP address: 192.168.20.14 Subnet Mask: 255.255.255.248 Default Gateway:192.168.20.9
B. IP address: 192.168.20.254 Subnet Mask: 255.255.255.0 Default Gateway:192.168.20.1
C. IP address: 192.168.20.30 Subnet Mask 255.255.255.248 Default Gateway:192.168.20.25
D. IP address: 192.168.20.30 Subnet Mask 255.255.255.240 Default Gateway:192.168.20.17
E. IP address: 192.168.20.30 Subnet Mask 255.255.255.240 Default Gateway:192.168.20.25

A. The command is used to establish a static route.
B. The default administrative distance is used.
C. The command is used to configure the default route.
D. The subnet mask for the source address is 255.255.255.0
E. The command is used to establish a stub network

A. TestKingRouter(config)# router ospf 0
B. TestKingRouter(config)# router ospf 1
C. TestKingRouter(config)# router ospf area 0
D. TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0
E. TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0
F. TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0

A. Point-to-point
B. Point to multipoint
C. Broadcast
D. Non-broadcast multi-access

A. All OSPF networks require the use of multiple areas
B. Multiple OSPF areas must connect to area 0
C. Single area OSPF networks must be configured in area 1
D. Areas can be assigned any number from 0 to 63535
E. Area 0 is called the backbone area
F. Each OSPF area need to be configured with a loopback interface

A. It confines network instability to a single area of network.
B. It increases the routing overhead of the network
C. It supports VLSM
D. It routes between Autonomous Systems.
E. It allows extensive control of routing updates

A. 1
B. 64
C. 1562
D. 64000
E. 1500