The network administrator has discover...

单项选择题X 纠错

The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network?（）

A. Lower the bridge priority number.
B. Change the MAC address of the switch.
C. Increase the VTP revision number for the domain.
D. Lower the root path cost on the switch ports.
E. Assign the switch an IP address with the lowest value.

参考答案：

进入题库练习

查答案就用赞题库小程序还有拍照搜题语音搜题快来试试吧

无需下载立即使用

你可能喜欢

单项选择题

Which command shows if an access list is assigned to an interface?（）

A. show ip interface [interface] access-lists
B. show ip access-lists interface [interface]
C. show ip interface [interface]
D. show ip access-lists [interface]

点击查看答案进入题库练习

单项选择题

A wireless client cannot connect to an 802.11b/g BSS with a b/g wireless card. The client section of the access point does not list any active WLAN clients. What is a possible reason for this?（）

A. The incorrect channel is configured on the client.
B. The client's IP address is on the wrong subnet.
C. The client has an incorrect pre-shared key.
D. The SSID is configured incorrectly on the client.

点击查看答案进入题库练习

单项选择题

What occurs on a Frame Relay network when the CIR is exceeded?（）

A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.

点击查看答案进入题库练习

单项选择题

A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices. What would be the most efficient way to configure MAC-level security on all these ports?（）

A. Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.
B. Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.
C. Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.
D. Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.

点击查看答案进入题库练习

单项选择题

What is the difference between a CSU/DSU and a modem?（）

A. A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signals from a router to a leased line.
B. A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signals from a router to a leased line.
C. A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signals from a router to a phone line.
D. A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signals from a router to a phone line.

点击查看答案进入题库练习

单项选择题

Which command reveals the last method used to powercycle a router?（）

A. show reload
B. show boot
C. show running-config
D. show version

点击查看答案进入题库练习

单项选择题

Which protocols are found in the network layer of the OSI reference model and are responsible for path determination and traffic switching?（）

A. LAN
B. routing
C. WAN
D. network

点击查看答案进入题库练习

单项选择题

Data transfer is slow between the source and destination. The quality of service requested by the transport layer in the OSI reference model is not being maintained. To fix this issue, at which layer should the troubleshooting process begin?（）

A. presentation
B. session
C. transport
D. network
E. physical