单项选择题X 纠错
A. Enable conversational learning on FabricPath vlans 1-10 for F-Series module
B. Enable FabricPath protocol on VLANs 1–10
C. No need for this command as conversational learning is enabled by default for all VLANs.
D. Enable conversational learning on Classical Ethernet VLAN for F-Series module
你可能喜欢
多项选择题
A. Cisco NX-OS Software does not support PIM dense mode.
B. The command ip multicast-routing must be enabled in Cisco NX-OS Software before any multicast configuration is possible on the switch.
C. PIM CLI configuration and verification commands are not available until you enable the PIM feature with the feature pim command.
D. Cisco NX-OS Software supports multicast routing per Layer 3 VRF instance.
E. The default PIM operational mode on the Cisco Nexus 7000 switch is SSM.
单项选择题
A. The L2 multicast frames are encapsulated in an OTV packet using the configured control-group multicast address for transport
B. The L2 multicast frames are dropped because multicast cannot be carried across the overlay
C. The L2 multicast frames are encapsulated in an OTV packet using the configured data-group multicast address for transport
D. The L2 multicast frames are forwarded natively across the overlay based on their multicast IDs
单项选择题
A. 128
B. 32
C. 64
D. Dependent on the number of switch IDs in the topology
单项选择题
A. IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.
B. The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.
C. IGMP snooping has been disabled on the VLAN 120 SVI.
D. IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.
E. IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
单项选择题
A. IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.
B. The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.
C. IGMP snooping has been disabled on the VLAN 120 SVI.
D. IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.
E. IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
单项选择题
A. Synchronizes ARP entries between vPC peers every five minutes
B. Triggers a manual update of ARP entries from the primary peer to the secondary
C. Enables a bulk loading of ARP entries when a vPC peer is restored
D. Uses the peer-keepalive link to maintain ARP table consistency
单项选择题
A. admin, operator, network-admin, and network-operator
B. admin, read-only, network-admin, and network-operator
C. vdc-admin, vdc-operator, network-admin, and network-operator
D. vdc-admin, vdc-operator, network-admin, and network-operator (for Nexus 7000) and network- admin and network-operator (for other Nexus switches)
E. admin and read-only
单项选择题
A. IGMP is not synchronized between vPC peers
B. Cisco Fabric Service carries IGMP entries across the vPC peer link
C. IP ARP synchronization under the vPC domain configuration also synchronizes IGMP
D. IGMP is flooded to the L2 domain, and there is no need to synchronize it between vPC peers
单项选择题
A. The OTV control-plane protocol uses the IS-IS protocol to establish adjacencies and exchange MAC reachability across the overlay network. You must enable IS-IS with the feature isis command before OTV adjacencies can be established.
B. OTV uses an SSM group range for neighbor discovery and to exchange MAC reachability with other OTV edge peers.
C. The OTV join interface is a routed uplink interface on the edge device used to physically join the overlay network.
D. The OTV internal interface encapsulates the site Layer 2 frames in IP unicast or multicast packets that are then sent to the other sites.
单项选择题
A. C84C·75FA·6000
B. 01005·E11.·2FD
C. C84C·76FA·6000
D. 4000.0000.0001